KJ보일러

본문 바로가기

팝업레이어 알림

팝업레이어 알림이 없습니다.
전체메뉴열기

주식회사 케이제이보일러 미래의 고효율 에너지기술과 지구의 환경을 선도하는 KJ보일러

수관식 패키지 보일러 고객 중심의 기업, 신뢰 받는 기업

Water Tube Packaged Boiler

수관식 패키지 보일러

■ KJ-P형 수관식 보일러는 컴퓨터 프로그램에 의한 최적형의 Boiler System입니다. 공기 예열기와 절탄기를 장착할 경우 배기가스에 의한 열 손실을 최소화하여 열효율을 극대화하였습니다. 또한 KJ-P형 수관식 보일러는 노벽과 측벽이 멤브레인 벽면으로 구성, 방사열의 손실을 최소화하였고, SOx와 NOx 등의 환경공해 문제에 적합하도록 Sizing 할 수 있습니다. 고압 스팀과 고온 스팀이 필요한 모든 공장, 건물, 아파트에 적합하며, 용량에 따라 3PASS (8T/H 이하)와 2PASS(10T/H 이상) 방식으로 설치면적을 최소화한 보일러로 외관 또한 미려하게 디자인하였습니다.

■ KJ-P type, water tube packaged boiler with air pre-heater and economizer attached, is suitable for all kinds of factories, buildings and apartment building required high pressure and temperature steam with its maximized thermal efficiency and minimized heat loss. It is structured to prevent environmental pollution cased by SOx or NOx. 3Pass is adequate to small capacity under 8T/H while 2Pass is good for large capacity over 8T/H. Also, it does not require large installation space and its exterior looks very elegantly.

Characteristics

특장점

■ 높은 열효율과 관리 비용 감소
특수 디자인, 컴퓨터 시뮬레이션 덕분에 높은 열효율이 보장 및 유지되므로 운전 비용을 쉽게 감소할 수 있습니다.
■ 완벽한 건조 스팀 생산
특수 스팀 분리기 덕분에 포밍(foaming)과 프라이밍이 방지되어, 건조 스팀을 생산하고 배관과 열 시설 수명을 늘릴 수 있습니다
■ 어떤 조건으로도 OK
KJ-P 타입 보일러는 방사열 표면 증가 때문에 로드(load) 변동을 감지할 수 있으므로 어떤 조건에서도 사용될 수 있습니다.
■ 보수 작업 용이
보일러의 옆과 뒷부분에 있는 많은 청소 Hole 및 Peep Hole을 설치하여 운전하는 동안 보일러가 청결한지 확인하기가 쉽도록 디자인되었습니다.
■ 설치 용이
간단한 구조로 현장에서 설치 조립 장소가 좁아도 가능하며, 입구가 아주 협소한 곳에도 설치 가능합니다.

■ High thermal efficiency and low maintenance cost
High thermal efficiency is guaranteed thanks to its special design and computer simulation. Therefore its operation cost is relatively lower than any other boilers.
■ Perfect dry steam production
As its special steam separator prevents foaming and priming, it can produce perfect dry steam and extend the life of pipes and heat facilities.
■ Under any condition, OK
KJ-P type boiler can flexibly perceive any load fluctuation thanks to its increased radiant heating surface. That means it is possible to use this type of boilers under any condition.
■ Easy repair work
It is designed to make it easy to check and clean with many cleaning holes located in the side and rear of boiler.
■ Easy installation
Owing to its simply structure, it can be assembled and installed in the spot in any small space. It is also possible to install even in area whose entrance is very narrow.

Schematic Drawing

구조도

Layout

배치도

Layout Dimension

배치사양

Flow Diagram

계통도

Specification

표준사양

  • 게시물이 없습니다.

회원로그인


그누보드5
주식회사 케이제이보일러 | 대표 이관종 | 사업자등록번호 135-86-40471
본사 : 경기도 용인시 수지구 광교중앙로 338, A동 601,602호 (광교우미뉴브)
공장 : 경기도 화성시 우정읍 버들로 797-50
Tel 031-8055-0851 | Fax 031-8055-0852
Copyright © 주식회사 케이제이보일러 All rights reserved.